Sealoflex Pink® is used:
- For temporary deck and low slope roof waterproofing over metal, concrete, and plywood
- As the base and saturation component of fully reinforced Sealoflex roofing applications including flashing, parapet wall, roof penetration, and other application details.
Sealoflex Pink®
Highly Elastic Acrylic Saturator for Sealoflex System
Sealoflex Pink® is a waterborne, single component acrylic coating. It cures to a tough rubber like material, which displays good adhesion and flexibility. Sealoflex Pink®, generally used along with Sealoflex polyester reinforcing fabric and Sealoflex Finish Coat™ to form a fully adhered single ply roofing membrane, is also used in conjunction with other Sealoflex products and systems to satisfy various waterproofing requirements.
Uses
Advantages
Sealoflex Pink® displays the following advantages:
- Does not become brittle with age
- Fast curing and may be applied in temperatures above 45°F
- Good low temperature flexibility
- Adheres to almost any roof or wall substrate including stucco, concrete, metal, brick, wood, asphalt, PVC, etc.
- VOC Compliant and environmentally friendly
- Tools and equipment wash up easily with water
Surface Preparation
Surfaces must be dry, clean and
free of dust, loosely adhering particles,
oil or grease.
Priming
No priming is necessary on unpainted wooden surfaces, asphalt, modified bitumen; PVC roofing membrane and weathered galvanized steel or non-ferrous metal. New galvanized steel must be thoroughly degreased and dry before applying Sealoflex Pink®.
Unprotected (ferrous metals)iron or steel:
Prime with Rust-X 2020™ followed by Sealoflex Metal Etch Primer™.
Concrete and masonry
Above grade: prime with Sealobond Primer WB™
On grade: prime with Sealoment Plus™. Use Dampseal 101 if “out gassing” is expected.
Structural Lightweight Concrete:
Prime with Dampseal 101.
Application
Sealoflex Pink® can be applied with a brush, roller or airless spray equipment.
Please refer to specific Sealoflex® System application guides for proper application requirements.
Cleaning
Uncured Sealoflex Pink® can be rinsed with water. Cured Sealoflex Pink® can be dissolved with Sealoflex Quickclean™ and rinsed with water.
Precautions
Do not apply Sealoflex Pink® if rain is imminent. Sealoflex Pink® will not cure when the ambient humidity exceeds 100% e.g. during periods of dew or fog. Curing will commence again once the humidity drops below 100%.
Check adhesion to previously painted surfaces as some surfaces may require special treatment or priming.
Contact our technical department for specific methods of testing. Do not use Sealoflex Pink® over Cellular Lightweight Concrete.
Important Notes
For this and/or related products, please refer to individual product data sheets, System Application Guides, Products MSDS, Primer Chart, Fabric Chart.
Color
Pink
Technical Data
|
Type: |
Acrylic Copolymer |
|
Shelf Life and |
12 months, unopened |
|
Application Temperature: |
45˚F to 105˚F (Ambient) |
|
Drying Time (Touch Dry): |
2 hours at 77˚F and 50% RH |
|
Elongation (ASTM D2370): |
61% (Reinforced) |
|
Water Vapor Transmission Rate (ASTM E96): |
3.2 grains/sq. ft./hour |
|
Tensile Strength (ASTM D412): |
3,109 psi (reinforced) |
|
Packaging: |
1, 5 and 55 gallon containers |
Coverage
Fabric reinforced application: 40 sq.ft./gal.
Temporary waterproofer: 100 sq.ft./gal. approximately.
Click above for larger image.